mirror of https://github.com/jeelabs/esp-link.git
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
70 lines
4.2 KiB
70 lines
4.2 KiB
<html>
|
|
<head><title>Help - ESP Link</title>
|
|
<link rel="stylesheet" type="text/css" href="style.css">
|
|
</head>
|
|
<body>
|
|
<div id="main">
|
|
<div id="topnav">%topnav%</div>
|
|
<h1><span class="esp">esp</span> link - Help</h1>
|
|
|
|
The ESP Link functions in two wifi modes: Station+AccessPoint (STA+AP) and Station (STA).
|
|
In the STA+AP mode it presents a network called esp8266 that you can connect to using the
|
|
password jeelabs8266. This mode is intended for initial configuration, but it is
|
|
fully functional. Typically the easiest way to connect to the esp8266 network is using a phone,
|
|
tablet, or laptop.</p>
|
|
<p>The recommended next step is to configure the ESP Link to connect to your "normal"
|
|
Wifi network so you can access it from any of your machines. Once you have connected the ESP Link
|
|
to your network and pointed your browser at it successfully, you should
|
|
switch the ESP Link to STA mode, which is more secure (no canned password).<p>
|
|
<p>In STA mode the ESP Link connects to the configured network (the info is saved in flash).
|
|
If, after a reset, it cannot connect for one minute, it automatically reverts to STA+AP mode
|
|
allowing you to reconnect to the esp8266 network to change configuration.</p>
|
|
<p>In STA mode the most tricky part usually is the IP address. On most networks, the ESP Link
|
|
will get a dynamic IP address assigned via DHCP and you now need to enter that IP address into
|
|
your browser to connect. The good news is that after you reset your ESP Link it will continue to
|
|
have the same IP address. However, if you leave it off for the week-end it will most likely get a
|
|
fresh IP the next time it starts up. On many Wifi routers you can enter a fixed mapping from
|
|
the ESP Link's hardware MAC address to a static IP address so it always gets the same IP
|
|
address. This is the recommended method of operation.</p>
|
|
|
|
<h1>Using your ESP Serial Programmer</h1>
|
|
The ESP Programmer can used in several distinct ways:
|
|
<ul>
|
|
<li>as a transparent bridge between TCP port 23 and the serial port</li>
|
|
<li>as a web console to see input from the serial port</li>
|
|
<li>as an Arduino, AVR, or ARM processor programmer using serial-over-TCP</li>
|
|
<li>as an Arduino, AVR, or ARM processor programmer by uploading HEX files (not yet functional)</li>
|
|
</ul>
|
|
|
|
<h2>Transparent bridge</h2>
|
|
<p>The ESP accepts TCP connections to port 23 and "connects" through to the serial port.
|
|
Up to 5 simultaneous TCP connections are supported and characters coming in on the serial
|
|
port get passed through to all connections. Characters coming in on a connection get copied
|
|
through to the serial port.</p>
|
|
<p>When using Linux a simple way to use this is <tt>nc esp8266 23</tt></p>
|
|
|
|
<h2>Programmer using serial-over-TCP</h2>
|
|
<p>By hooking up the ESP's GPIO lines to the reset line of an Arduino (or AVR in general) that is
|
|
preloaded with the Optiboot bootloader/flasher it is possible to reprogram these processors over
|
|
Wifi. The way is works is that the ESP toggles the reset line each time a connection is established
|
|
and the first characters are the flash programming synchronization sequence.</p>
|
|
<p>When using Linux avrdude can be instructed to program an AVR over TCP by using a special syntax
|
|
for the serial port: <tt>-Pnet:esp8266:23</tt>, where <tt>esp8266</tt> is the hostname of the ESP
|
|
Serial Programmer (an IP address could have been used instead).</p>
|
|
<p>NXP's LPC800-serial ARM processors can be programmed similarly by hooking up GPIO pins to the
|
|
ARM's reset and ISP lines. The ESP Serial Programmer issues the correct reset/isp pulses to put
|
|
the ARM chip into firmware programming mode.</p>
|
|
|
|
<h2>Web Console</h2>
|
|
<p>The output of an attached Arduino/AVR/ARM can also be monitored via the console web page.
|
|
When connecting, it shows the most recent 10KB of characters received on the serial port and
|
|
then continues to print everything that comes in on the serial port. Eventually the page refreshes
|
|
when it gets very long. (Yes, this could be improved with some javascript...)</p>
|
|
|
|
<h2>Programmer using HEX upload</h2>
|
|
<p><i>(Not yet functional)</i> Instead of using the wifi-to-serial bridge to program
|
|
microcontrollers it is often faster to upload the HEX file to the ESP Serial Programmer and
|
|
have it perform the actual programming protocol.</p>
|
|
|
|
</div>
|
|
</body></html>
|
|
|