boblark
2 years ago
parent
624f14283e
commit
3319cfa8cb
@ -0,0 +1,177 @@ |
||||
// WavFilePlayer.ino
|
||||
//
|
||||
// WAV file player, mono, multi-rate example
|
||||
// Output is Digital I2S - Used with the audio shield:
|
||||
//
|
||||
// The SD card may connect to different pins, depending on the
|
||||
// hardware you are using. Configure the SD card
|
||||
// pins to match your hardware. It is set for T4.x Rev D PJRC
|
||||
// Teensy Audio Adaptor card here.
|
||||
//
|
||||
// Your microSD card must have the WAV files loaded to it:
|
||||
// W9GR48.WAV
|
||||
// W9GR12.WAV
|
||||
// These are at
|
||||
// https://github.com/chipaudette/OpenAudio_ArduinoLibrary/blob/master/utility/
|
||||
//
|
||||
// INO based on PJRC file of the same name, but converted to work with the
|
||||
// OpenAudio_ArduinoLibrary with floating point F32 audio.
|
||||
// Provision has been added for
|
||||
// WAV files with sub-multiple sampling rates, relative to Audio rate.
|
||||
// The latter adds an optional .INO defined FIR filter just before the
|
||||
// audio is transmitted from the AudioSDPlayer_F32 update function. This
|
||||
// filter is needed for sub-multiple WAV rates, but is available for any
|
||||
// place it is helpful. Comments to Bob Larkin. Jan 2023
|
||||
//
|
||||
// This example is monoraural only, but demonstrates 12 ksps sampling
|
||||
// in the WAV file. See the other example, wavPlayerStereo.ino
|
||||
// that uses stereo files, like the original I16 library
|
||||
// example did.
|
||||
// This example code is in the public domain.
|
||||
|
||||
#include <Audio.h> |
||||
#include <Wire.h> |
||||
#include <SPI.h> |
||||
#include <SD.h> |
||||
#include "OpenAudio_ArduinoLibrary.h" |
||||
|
||||
// This INO is setup to run audio sample rate at 48 ksps but the WAV file
|
||||
// can be either 48 ksps or 12 ksps. There are multiple W9GR files at different
|
||||
// sample rates. Select by SUB_MULT of 1 or 4.
|
||||
#define SUB_MULT 1 |
||||
|
||||
// T3.x supported sample rates: 2000, 8000, 11025, 16000, 22050, 24000, 32000, 44100, 44117, 48000,
|
||||
// 88200, 88235 (44117*2), 95680, 96000, 176400, 176470, 192000
|
||||
// T4.x supports any sample rate the codec will hanedle.
|
||||
const float sample_rate_Hz = 48000.0f; |
||||
const int audio_block_samples = 128; // Always 128, which is AUDIO_BLOCK_SAMPLES from AudioStream.h
|
||||
AudioSettings_F32 audio_settings(sample_rate_Hz, audio_block_samples); |
||||
|
||||
AudioSDPlayer_F32 playWav1(audio_settings); |
||||
AudioAnalyzeRMS_F32 rms1; |
||||
AudioAnalyzeRMS_F32 rms2; |
||||
AudioOutputI2S_F32 audioOutput(audio_settings); |
||||
AudioConnection_F32 patchCord1(playWav1, 0, audioOutput, 0); |
||||
AudioConnection_F32 patchCord3(playWav1, 0, rms1, 0); |
||||
AudioConnection_F32 patchCord4(playWav1, 1, rms2, 0); |
||||
AudioConnection_F32 patchCord2(playWav1, 1, audioOutput, 1); |
||||
AudioControlSGTL5000 sgtl5000_1; |
||||
|
||||
// Use these with the Teensy 4.x Rev D Audio Shield (NOT for T3.x)
|
||||
#define SDCARD_CS_PIN 10 |
||||
#define SDCARD_MOSI_PIN 11 |
||||
#define SDCARD_SCK_PIN 13 |
||||
|
||||
#if SUB_MULT==4 |
||||
/* This filter is a LPF to smooth out the zero data added for interpolation
|
||||
* of the sample rate. It is a |
||||
* FIR filter designed with http://t-filter.appspot.com
|
||||
* Sampling frequency: 48000 Hz |
||||
* 0 Hz - 3000 Hz ripple = 0.12 dB |
||||
* 6000 Hz - 24000 Hz atten min = -62.17 dB */ |
||||
static float32_t fir3k48k[45] = { |
||||
-0.00111325f,-0.00202997f,-0.00306939f,-0.00351866f,-0.00274389f,-0.00035614f, |
||||
0.00346572f, 0.00778335f, 0.01098197f, 0.01119770f, 0.00702222f,-0.00172373f, |
||||
-0.01344104f,-0.02471188f,-0.03091211f,-0.02741134f,-0.01105157f, 0.01854769f, |
||||
0.05833902f, 0.10214361f, 0.14192191f, 0.16971322f, 0.17968923f, 0.16971322f, |
||||
0.14192191f, 0.10214361f, 0.05833902f, 0.01854769f,-0.01105157f,-0.02741134f, |
||||
-0.03091211f,-0.02471188f,-0.01344104f,-0.00172373f, 0.00702222f, 0.01119770f, |
||||
0.01098197f, 0.00778335f, 0.00346572f,-0.00035614f,-0.00274389f,-0.00351866f, |
||||
-0.00306939f,-0.00202997f,-0.00111325f}; |
||||
|
||||
// CMSIS FIR requires the following buffers
|
||||
float32_t firBufferL[128+45-1]; |
||||
float32_t firBufferR[128+45-1]; |
||||
#endif |
||||
|
||||
/* subMult is a global struct definition from AudioSDPlayer_F32.h
|
||||
* struct subMult { |
||||
* uint16_t rateRatio; // Should be 1 for no rate change, else 2, 4, 8
|
||||
* uint16_t numCoeffs; // FIR filter for interpolation
|
||||
* float32_t* firCoeffs; // FIR Filter Coeffs
|
||||
* float32_t* firBufferL; // pointer to 127 + numCoeffs float32_t, left ch
|
||||
* float32_t* firBufferR; // pointer to 127 + numCoeffs float32_t, right ch
|
||||
* }; |
||||
*/ |
||||
#if SUB_MULT==4 |
||||
// Both buffers are left for mono.
|
||||
struct subMult wavQuarter = {4, 45, fir3k48k, firBufferL, firBufferL}; |
||||
// Next a sample of subMult for no interpolation and no FIR filter
|
||||
#else |
||||
struct subMult wavQuarter = {1, 0, NULL, NULL, NULL}; |
||||
#endif |
||||
// And next is a sample of no interpolation, but borrowing the FIR filter
|
||||
// for some non-interpolation reason.
|
||||
// struct subMult wavQuarter = {1, 45, fir3k48k, firBufferL, firBufferL};
|
||||
|
||||
// wavData is a global struct, definined in AudioSDPlayer_F32.h
|
||||
// This provides information about the current WAV file to this .INO
|
||||
struct wavData* pCurrentWavData; |
||||
|
||||
void setup() { // ********** SETUP **********
|
||||
Serial.begin(9600); delay(1000); |
||||
Serial.println("*** F32 WAV from SD Card ***"); |
||||
|
||||
AudioMemory_F32(30, audio_settings); |
||||
|
||||
pCurrentWavData = playWav1.getCurrentWavData(); |
||||
|
||||
sgtl5000_1.enable(); |
||||
audioOutput.setGain(0.05); // <<< Output volume control
|
||||
|
||||
SPI.setMOSI(SDCARD_MOSI_PIN); |
||||
SPI.setSCK(SDCARD_SCK_PIN); |
||||
Serial.print("SD.begin() returns "); Serial.println(SD.begin(SDCARD_CS_PIN)); |
||||
} |
||||
|
||||
void playFile(const char *filename) |
||||
{ |
||||
Serial.println(""); |
||||
Serial.print("Playing file: "); |
||||
Serial.println(filename); |
||||
|
||||
// Allow for running the WAV file at a sub-rate from the Audio rate
|
||||
// Two of these are defined above for 1 and 4 sub rates.
|
||||
playWav1.setSubMult(&wavQuarter); |
||||
|
||||
// Start playing the file. This sketch continues to
|
||||
// run while the file plays.
|
||||
playWav1.play(filename); |
||||
|
||||
// A brief delay for the library read WAV info
|
||||
delay(25); |
||||
|
||||
Serial.print("WAV file format = "); Serial.println(pCurrentWavData->audio_format); |
||||
Serial.print("WAV number channels = "); Serial.println(pCurrentWavData->num_channels); |
||||
Serial.print("WAV File Sample Rate = "); Serial.println(pCurrentWavData->sample_rate); |
||||
Serial.print("Number of bits per Sample = "); Serial.println(pCurrentWavData->bits); |
||||
Serial.print("File length, seconds = "); |
||||
Serial.println(0.001f*(float32_t)playWav1.lengthMillis(), 3); |
||||
|
||||
// Simply wait for the file to finish playing.
|
||||
while (playWav1.isPlaying()) |
||||
{ |
||||
Serial.print("RMS "); |
||||
delay(1000); |
||||
if(rms1.available()) |
||||
Serial.print(rms1.read(),5); |
||||
Serial.print(" L R "); |
||||
if(rms2.available()) |
||||
Serial.print(rms2.read(),5); |
||||
// Time in seconds
|
||||
Serial.print(" t="); |
||||
Serial.println(0.001f*(float32_t)playWav1.positionMillis(), 3); |
||||
} |
||||
Serial.println(""); |
||||
} |
||||
|
||||
void loop() { |
||||
#if SUB_MULT==4 |
||||
playFile("W9GR12.WAV"); // filenames are always uppercase 8.3 format
|
||||
#elif SUB_MULT==1 |
||||
playFile("W9GR48.WAV"); |
||||
#else |
||||
Serial.println("**** Non-used SUB_MULT. Use 1 or 4. ****"); |
||||
#endif |
||||
delay(500); |
||||
} |
||||
@ -0,0 +1,133 @@ |
||||
// WavFilePlayer2.ino
|
||||
//
|
||||
// WAV file player, stereo, 44.1 ksps example
|
||||
// Output is Digital I2S - Used with the audio shield:
|
||||
//
|
||||
// The SD card may connect to different pins, depending on the
|
||||
// hardware you are using. Configure the SD card
|
||||
// pins to match your hardware. It is set for T4.x Rev D PJRC
|
||||
// Teensy Audio Adaptor card here.
|
||||
//
|
||||
// Your microSD card must have the WAV files loaded to it:
|
||||
// SDTEST1.WAV
|
||||
// SDTEST2.WAV
|
||||
// SDTEST3.WAV
|
||||
// SDTEST4.WAV
|
||||
// These are PJRC Teensy I16 library test files and are at
|
||||
// http://www.pjrc.com/teensy/td_libs_AudioDataFiles.html
|
||||
//
|
||||
// INO based on PJRC file of the same name, but converted to work with the
|
||||
// OpenAudio_ArduinoLibrary with floating point F32 audio.
|
||||
// Provision has been added for
|
||||
// WAV files with sub-multiple sampling rates, relative to Audio rate.
|
||||
// The latter adds an optional .INO defined FIR filter just before the
|
||||
// audio is transmitted from the AudioSDPlayer_F32 update function. This
|
||||
// filter is needed for sub-multiple WAV rates, but is available for any
|
||||
// place it is helpful. Comments to Bob Larkin. Jan 2023
|
||||
//
|
||||
// This example is stereo only, but demonstrates 12 ksps sampling
|
||||
// in the WAV file. See the other example, wavPlayer.ino
|
||||
// that uses monaural files with 2 different sample rates.
|
||||
//
|
||||
// This example code is in the public domain.
|
||||
|
||||
#include <Audio.h> |
||||
#include <Wire.h> |
||||
#include <SPI.h> |
||||
#include <SD.h> |
||||
#include "OpenAudio_ArduinoLibrary.h" |
||||
|
||||
// This INO is setup to run audio sample rate at 44.1 ksps
|
||||
|
||||
// T3.x supported sample rates: 2000, 8000, 11025, 16000, 22050, 24000, 32000, 44100, 44117, 48000,
|
||||
// 88200, 88235 (44117*2), 95680, 96000, 176400, 176470, 192000
|
||||
// T4.x supports any sample rate the codec will hanedle.
|
||||
const float sample_rate_Hz = 44100.0f; |
||||
const int audio_block_samples = 128; // Always 128, which is AUDIO_BLOCK_SAMPLES from AudioStream.h
|
||||
AudioSettings_F32 audio_settings(sample_rate_Hz, audio_block_samples); |
||||
|
||||
AudioSDPlayer_F32 playWav1(audio_settings); |
||||
AudioAnalyzeRMS_F32 rms1; |
||||
AudioAnalyzeRMS_F32 rms2; |
||||
AudioOutputI2S_F32 audioOutput(audio_settings); |
||||
AudioConnection_F32 patchCord1(playWav1, 0, audioOutput, 0); |
||||
AudioConnection_F32 patchCord3(playWav1, 0, rms1, 0); |
||||
AudioConnection_F32 patchCord4(playWav1, 1, rms2, 0); |
||||
AudioConnection_F32 patchCord2(playWav1, 1, audioOutput, 1); |
||||
AudioControlSGTL5000 sgtl5000_1; |
||||
|
||||
// Use these with the Teensy 4.x Rev D Audio Shield (NOT for T3.x)
|
||||
#define SDCARD_CS_PIN 10 |
||||
#define SDCARD_MOSI_PIN 11 |
||||
#define SDCARD_SCK_PIN 13 |
||||
|
||||
// subMult allows slower rates for the WAV files. Not used here
|
||||
//struct subMult wavNormal = {1, 0, NULL, NULL, NULL};
|
||||
|
||||
// wavData is a global struct, definined in AudioSDPlayer_F32.h
|
||||
// This provides information about the current WAV file to this .INO
|
||||
struct wavData* pCurrentWavData; |
||||
|
||||
void setup() { // ********** SETUP **********
|
||||
Serial.begin(9600); delay(1000); |
||||
Serial.println("*** F32 WAV from SD Card ***"); |
||||
|
||||
AudioMemory_F32(30, audio_settings); |
||||
|
||||
pCurrentWavData = playWav1.getCurrentWavData(); |
||||
|
||||
sgtl5000_1.enable(); |
||||
audioOutput.setGain(0.05); // <<< Output volume control
|
||||
|
||||
SPI.setMOSI(SDCARD_MOSI_PIN); |
||||
SPI.setSCK(SDCARD_SCK_PIN); |
||||
Serial.print("SD.begin() returns "); |
||||
Serial.println(SD.begin(SDCARD_CS_PIN)); // Opens the microSD card
|
||||
} |
||||
|
||||
void playFile(const char *filename) { |
||||
Serial.println(""); |
||||
Serial.print("Playing file: "); |
||||
Serial.println(filename); |
||||
|
||||
// Start playing the file. This sketch continues to
|
||||
// run while the file plays.
|
||||
playWav1.play(filename); |
||||
|
||||
// A brief delay for the library read WAV info
|
||||
delay(25); |
||||
|
||||
Serial.print("WAV file format = "); Serial.println(pCurrentWavData->audio_format); |
||||
Serial.print("WAV number channels = "); Serial.println(pCurrentWavData->num_channels); |
||||
Serial.print("WAV File Sample Rate = "); Serial.println(pCurrentWavData->sample_rate); |
||||
Serial.print("Number of bits per Sample = "); Serial.println(pCurrentWavData->bits); |
||||
Serial.print("File length, seconds = "); |
||||
Serial.println(0.001f*(float32_t)playWav1.lengthMillis(), 3); |
||||
|
||||
// Simply wait for the file to finish playing.
|
||||
while (playWav1.isPlaying()) |
||||
{ |
||||
Serial.print("RMS "); |
||||
delay(1000); |
||||
if(rms1.available()) |
||||
Serial.print(rms1.read(),5); |
||||
Serial.print(" L R "); |
||||
if(rms2.available()) |
||||
Serial.print(rms2.read(),5); |
||||
// Time in seconds
|
||||
Serial.print(" t="); |
||||
Serial.println(0.001f*(float32_t)playWav1.positionMillis(), 3); |
||||
} |
||||
Serial.println(""); |
||||
} |
||||
|
||||
void loop() { |
||||
playFile("SDTEST1.WAV"); // filenames are always uppercase 8.3 format
|
||||
delay(500); |
||||
playFile("SDTEST2.WAV"); |
||||
delay(500); |
||||
playFile("SDTEST3.WAV"); |
||||
delay(500); |
||||
playFile("SDTEST4.WAV"); |
||||
delay(500); |
||||
} |
||||
Loading…
Reference in new issue