|
SdFs
|
configuration definitions More...
Macros | |
| #define | DESTRUCTOR_CLOSES_FILE 0 |
| #define | ENABLE_ARDUINO_FEATURES 1 |
| #define | ENDL_CALLS_FLUSH 0 |
| #define | FAT12_SUPPORT 0 |
| #define | MAINTAIN_FREE_CLUSTER_COUNT 0 |
| #define | USE_LONG_FILE_NAMES 1 |
| #define | USE_MULTI_SECTOR_IO 1 |
| #define | USE_SEPARATE_FAT_CACHE 0 |
configuration definitions
Copyright (c) 20011-2017 Bill Greiman This file is part of the SdFs library for SD memory cards.
MIT License
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
| #define DESTRUCTOR_CLOSES_FILE 0 |
Set DESTRUCTOR_CLOSES_FILE non-zero to close a file in its destructor.
Causes use of lots of heap in ARM.
| #define ENABLE_ARDUINO_FEATURES 1 |
Enable Extra features for Arduino.
| #define ENDL_CALLS_FLUSH 0 |
Call flush for endl if ENDL_CALLS_FLUSH is non-zero
The standard for iostreams is to call flush. This is very costly for SdFat. Each call to flush causes 2048 bytes of I/O to the SD.
SdFat has a single 512 byte buffer for I/O so it must write the current data sector to the SD, read the directory sector from the SD, update the directory entry, write the directory sector to the SD and read the data sector back into the buffer.
The SD flash memory controller is not designed for this many rewrites so performance may be reduced by more than a factor of 100.
If ENDL_CALLS_FLUSH is zero, you must call flush and/or close to force all data to be written to the SD.
| #define FAT12_SUPPORT 0 |
Allow FAT12 volumes if FAT12_SUPPORT is non-zero. FAT12 has not been well tested.
| #define MAINTAIN_FREE_CLUSTER_COUNT 0 |
Set MAINTAIN_FREE_CLUSTER_COUNT nonzero to keep the count of free clusters updated. This will increase the speed of the freeClusterCount() call after the first call. Extra flash will be required.
| #define USE_LONG_FILE_NAMES 1 |
Set USE_LONG_FILE_NAMES nonzero to use long file names (LFN). Long File Name are limited to a maximum length of 255 characters.
This implementation allows 7-bit characters in the range 0X20 to 0X7E. The following characters are not allowed:
< (less than)
(greater than)
: (colon) " (double quote) / (forward slash) \ (backslash) | (vertical bar or pipe) ? (question mark)
| #define USE_MULTI_SECTOR_IO 1 |
Set USE_MULTI_SECTOR_IO non-zero to use multi-sector SD read/write.
Don't use mult-sector read/write on small AVR boards.
| #define USE_SEPARATE_FAT_CACHE 0 |
Set USE_SEPARATE_FAT_CACHE non-zero to use a second 512 byte cache for FAT table entries. Improves performance for large writes that are not a multiple of 512 bytes.
1.8.10
