V0.5

DFRobot_AS3935_I2C.cpp

@@ -46,18 +46,18 @@ void DFRobot_AS3935_I2C::singRegWrite(uint8_t regAdd, uint8_t dataMask, uint8_t
 
     // finally, write the data to the register
     I2c.write(devAdd, regAdd, newRegData);
-    Serial.print("wrt: ");
-    Serial.print(newRegData,HEX);
-    Serial.print(" Act: ");
-    Serial.println(singRegRead(regAdd),HEX);
+    //Serial.print("wrt: ");
+    //Serial.print(newRegData,HEX);
+    //Serial.print(" Act: ");
+    //Serial.println(singRegRead(regAdd),HEX);
 }
 
 void DFRobot_AS3935_I2C::defInit()
 {
-    AS3935Reset();            // reset registers to default
+    reset();            // reset registers to default
 }
 
-void DFRobot_AS3935_I2C::AS3935Reset()
+void DFRobot_AS3935_I2C::reset()
 {
     // run PRESET_DEFAULT Direct Command to set all registers in default state
     I2c.write(devAdd, (uint8_t)0x3C, (uint8_t)0x96);
@@ -240,7 +240,7 @@ void DFRobot_AS3935_I2C::setNoiseFloorLvl(uint8_t nfSel)
 {
     // NF settings addres 0x01, bits 6:4
     // default setting of 010 at startup (datasheet, table 9)
-    if(7 >= nfSel)                                // nf_sel within expected range
+    if(7 >= nfSel)                                // nfSel within expected range
     {
         singRegWrite(0x01, 0x70, ((nfSel & 0x07) << 4));
     }

DFRobot_AS3935_I2C.h

@@ -22,8 +22,6 @@ class DFRobot_AS3935_I2C
     void manualCal(uint8_t capacitance, uint8_t location, uint8_t disturber);
     /*! reset registers to default */
     void defInit(void);
-    void powerUp(void);
-    void powerDown(void);
     void disturberEn(void);
     void disturberDis(void);
     void setIRQOutputSource(uint8_t irqSelect);
@@ -52,7 +50,9 @@ class DFRobot_AS3935_I2C
     uint8_t irq, devAdd;
     uint8_t singRegRead(uint8_t regAdd);
     void singRegWrite(uint8_t regAdd, uint8_t dataMask, uint8_t regData);
-    void AS3935Reset(void);
+    void reset(void);
+    void powerUp(void);
+    void powerDown(void);
     void calRCO(void);
 };
 

examples/DFRobot_AS3935_lightning_sensor_detailed/DFRobot_AS3935_lightning_sensor_detailed.ino

@@ -0,0 +1,140 @@
+/*!
+   file DFRobot_AS3935_lightning_sensor.ino
+
+   SEN0290 Lightning Sensor
+   This sensor can detect lightning and display the distance and intensity of the lightning within 40 km
+   It can be set as indoor or outdoor mode.
+   The module has three I2C, these addresses are:
+   AS3935_ADD1  0x01   A0 = High  A1 = Low
+   AS3935_ADD3  0x03   A0 = High  A1 = High
+   AS3935_ADD2  0x02   A0 = Low   A1 = High
+
+   Copyright    [DFRobot](http://www.dfrobot.com), 2018
+   Copyright    GNU Lesser General Public License
+
+   version  V0.4
+   date  2018-11-15
+*/
+
+#include "Lib_I2C.h"
+#include "DFRobot_AS3935_I2C.h"
+
+volatile int8_t AS3935IsrTrig = 0;
+
+#define IRQ_PIN              2
+
+// Antenna tuning capcitance (must be integer multiple of 8, 8 - 120 pf)
+#define AS3935_CAPACITANCE   96
+
+// Indoor/outdoor mode selection
+#define AS3935_INDOORS       0
+#define AS3935_OUTDOORS      1
+#define AS3935_MODE          AS3935_INDOORS
+
+// Enable/disable disturber detection
+#define AS3935_DIST_DIS      0
+#define AS3935_DIST_EN       1
+#define AS3935_DIST          AS3935_DIST_EN
+
+// I2C address
+#define AS3935_I2C_ADDR       AS3935_ADD2
+
+void AS3935_ISR();
+
+DFRobot_AS3935_I2C  lightning0((uint8_t)IRQ_PIN, (uint8_t)AS3935_I2C_ADDR);
+
+void setup()
+{
+
+  Serial.begin(115200);
+  Serial.println("DFRobot AS3935 lightning sensor begin!");
+
+  // Setup for the the I2C library: (enable pullups, set speed to 400kHz)
+  I2c.begin();
+  I2c.pullup(true);
+  I2c.setSpeed(1);
+  delay(2);
+
+  lightning0.setI2CAddress(AS3935_ADD3);
+  // Set registers to default
+  lightning0.defInit();
+  // Configure sensor
+  lightning0.manualCal(AS3935_CAPACITANCE, AS3935_MODE, AS3935_DIST);
+  
+  //set indoors or outdoors models
+  lightning0.setIndoors();
+  //lightning0.setOutdoors();
+
+  //disturber detection
+  lightning0.disturberEn();
+  //lightning0.disturberDis();
+  
+  // Enable interrupt (connect IRQ pin IRQ_PIN: 2, default)
+//  Connect the IRQ and GND pin to the oscilloscope.
+//  uncomment the following sentences to fine tune the antenna for better performance.
+//  This will dispaly the antenna's resonance frequency/16 on IRQ pin (The resonance frequency will be divided by 16 on this pin)
+//  Tuning AS3935_CAPACITANCE to make the frequency within 500/16 kHz ± 3.5%
+//  lightning0.setLcoFdiv(0);
+//  lightning0.setIRQOutputSource(3);
+
+// Set the noise level,use a default value greater than 7
+  lightning0.setNoiseFloorLvl(2);
+  //uint8_t noiseLv = lightning0.getNoiseFloorLvl();
+
+//used to modify WDTH,alues should only be between 0x00 and 0x0F (0 and 7)
+  lightning0.setWatchdogThreshold(0);
+  //uint8_t wtdgThreshold = lightning0.getWatchdogThreshold();
+
+//used to modify SREJ (spike rejection),values should only be between 0x00 and 0x0F (0 and 7)
+  lightning0.setSpikeRejection(2);
+  //uint8_t spikeRejection = lightning0.getSpikeRejection();
+
+  attachInterrupt(0, AS3935_ISR, RISING);
+
+}
+
+void loop()
+{
+  // It does nothing until an interrupt is detected on the IRQ pin.
+  while (AS3935IsrTrig == 0) {}
+  delay(5);
+
+  // Reset interrupt flag
+  AS3935IsrTrig = 0;
+
+  // Get interrupt source
+  uint8_t intSrc = lightning0.getInterruptSrc();
+  if (intSrc == 1)
+  {
+    // Get rid of non-distance data
+    uint8_t lightningDistKm = lightning0.getLightningDistKm();
+    Serial.println("Lightning occurs!");
+    Serial.print("Distance: ");
+    Serial.print(lightningDistKm);
+    Serial.println(" km");
+
+    // Get lightning energy intensity
+    uint32_t lightningEnergyVal = lightning0.getStrikeEnergyRaw();
+    Serial.print("Intensity: ");
+    Serial.print(lightningEnergyVal);
+    Serial.println("");
+  }
+  else if (intSrc == 2)
+  {
+    Serial.println("Disturber discovered!");
+  }
+  else if (intSrc == 3)
+  {
+    Serial.println("Noise level too high!");
+  }
+  
+  //View register data
+  //lightning0.printAllRegs();
+}
+
+//IRQ handler for AS3935 interrupts
+void AS3935_ISR()
+{
+  AS3935IsrTrig = 1;
+}
+

keywords.txt

@@ -27,8 +27,6 @@ receive	KEYWORD2
 setI2CAddress	KEYWORD2
 manualCal	KEYWORD2
 defInit	KEYWORD2
-powerUp	KEYWORD2
-powerDown	KEYWORD2
 disturberEn	KEYWORD2
 disturberDis	KEYWORD2
 setIRQOutputSource	KEYWORD2

readme.md

@@ -134,6 +134,48 @@ void setLcoFdiv(uint8_t fdiv);
  */
 void setIRQOutputSource(uint8_t irqSelect);
 
+/*
+ * @brief Set the noise level
+ *
+ * @param 0~7,More than 7 will use the default value:2
+ */
+void setNoiseFloorLvl(uint8_t nfSel);
+
+/*
+ * @brief Get the noise level
+ *
+ * @return 0~7
+ */
+uint8_t getNoiseFloorLvl(void);
+
+/*
+ * @brief Set an anti-interference rating
+ *
+ * @param 0~7,More than 7 will use the default value:1
+ */
+void setWatchdogThreshold(uint8_t wdth);
+
+/*
+ * @brief read WDTH
+ *
+ * @return 0~7
+ */
+uint8_t getWatchdogThreshold(void);
+
+/*
+ * @brief Modify SREJ (spike rejection)
+ *
+ * @param 0~7,More than 7 will use the default value:2
+ */
+void setSpikeRejection(uint8_t srej);
+
+/*
+ * @brief read SREJ (spike rejection)
+ *
+ * @return 0~7
+ */
+uint8_t getSpikeRejection(void);
+
 ```