Skip to content

AutoConnect menu

Luxbar

The AutoConnect menu is developed using the LuxBar which is licensed under the MIT License. See the License.

Where the from

The AutoConnect menu appears when you access the AutoConnect root path. It is assigned "/_ac" located on the local IP address of ESP8266/ESP32 module by default. This location can be changed in the sketch. The following screen will appear at access to http://{localIP}/_ac as the root path. This is the statistics of the current WiFi connection. You can access the menu from the here, to invoke it tap at right on top. (e.g. http://192.168.244.1/_ac for SoftAP mode.)

What's the local IP?

A local IP means Local IP at connection established or SoftAP's IP.

Right on top

Currently, AutoConnect supports four menus. Undermost menu as "HOME" returns to the home path of its sketch.

  • Configure new AP: Configure SSID and Password for new access point.
  • Open SSIDs: Opens the past SSID which has been established connection from EEPROM.
  • Disconnect: Disconnects current connection.
  • Reset...: Rest the ESP8266/ESP32 module.
  • HOME: Return to user home page.

Configure new AP

Scan all available access point in the vicinity and display it. Strength and security of the detected AP are marked. The is indicated for the SSID that needs a security key. "Hidden:" means the number of hidden SSIDs discovered.
Enter SSID and Passphrase and tap "apply" to starts WiFi connection.

Open SSIDs

Once it was established WiFi connection, its SSID and password will be saved in EEPROM of ESP8266/ESP32 automatically. The Open SSIDs menu reads the saved SSID credentials from the EEPROM. The stored credential data are listed by the SSID as shown below. Its label is a clickable button. Tap the SSID button, starts WiFi connection it.

Disconnect

Disconnect ESP8266/ESP32 from the current connection. It can also reset the ESP8266/ESP32 automatically after disconnection by instructing with using API in the sketch.

After tapping "Disconnect", you will not be able to reach the AutoConnect menu. Once disconnected, you will need to set the SSID again for connecting the WLAN.

Reset...

Reset the ESP8266/ESP32 module, it will start rebooting. After rebooting complete, the ESP8266/ESP32 module begins establishing the previous connection with WIFI_STA mode, and esp8266ap or esp32ap of an access point will disappear from WLAN.

Not every ESP8266 module will be rebooted normally

The Reset menu is using the ESP.reset() function for ESP8266. This is an almost hardware reset. In order to resume the sketch normally, the state of GPIO0 is important. Since this depends on the circuit implementation for each module, not every module will be rebooted normally. See also FAQ.

Custom menu items

The menu items of the custom Web page line up at the below in the AutoConnect menu if the custom Web pages are joined. Details for Custom Web pages in AutoConnect menu.

HOME

A HOME item located at the bottom of the menu list is a link to the home path. The URI as the home path is / by default, and it is defined by AUTOCONNECT_HOMEURI with AutoConnectDefs.h file.

#define AUTOCONNECT_HOMEURI     "/"

You can change the HOME path using the AutoConnect API. The AutoConnect::home function sets the URI as a link of the HOME item of the AutoConnect menu.

Extend AutoConnect menu with your sketches

The AutoConnect menu can contain custom items of your own sketch. It works for the custom Web pages by AutoConnectAux, addition to the request handler for ESP8266WebServer class that is registered by the ESP8266WebServer::on function or WebServer::on for ESP32. That is, you can make it as a menu item to invoke a legacy web page. The below screenshot is the result of adding an example sketch for the ESP8266WebServer library known as FSBrowser to the AutoConnect menu item. It adds Edit and List items with little modification of the legacy sketch code.

The procedure to extend the AutoConnect menu is described in the Advanced usage section.