forked from wirtz/BALibrary
parent
8da7c42d98
commit
306691e6e0
@ -0,0 +1,121 @@ |
||||
/*************************************************************************
|
||||
* This demo uses only the built-in libraries provided with the Arudino |
||||
* Teensy libraries.
|
||||
*
|
||||
* IT IS STRONGLY RECOMMENDED to use the BAGuitar Library located at |
||||
* https://github.com/Blackaddr/BAGuitar
|
||||
* The BAGuitar library will made it easier to use the features of your |
||||
* GTA Pro board, as well and configure it correctly to eliminate |
||||
* unneccesary noise. |
||||
*
|
||||
* The built-in support for the WM8731 codec in the Teensy Library is very |
||||
* limited. Without proper configuration, the codec will produce a noisy |
||||
* output. This is caused by the default configuration the WM8731 powers |
||||
* up in. This can easily be corrected by installing the BAGuitar library |
||||
*
|
||||
* For instructions on installing additional libraries follow the |
||||
* instructions at https://www.arduino.cc/en/Guide/Libraries after downloading
|
||||
* the BAGuitar repo from github as a zip file. |
||||
*
|
||||
*/ |
||||
|
||||
#include <Wire.h> |
||||
#include <Audio.h> |
||||
#include <MIDI.h> |
||||
|
||||
AudioInputI2S i2sIn; |
||||
AudioOutputI2S i2sOut; |
||||
|
||||
// Audio connections, just connect the I2S input directly to the I2S output.
|
||||
AudioConnection patch0(i2sIn,0, i2sOut, 0); |
||||
AudioConnection patch1(i2sIn,1, i2sOut, 1); |
||||
|
||||
AudioControlWM8731 codecControl; // needed to enable the codec
|
||||
|
||||
unsigned long t=0; |
||||
const int usrLED = 16; // the location of the GTA Pro user LED (not the LED on the Teensy itself)
|
||||
int usrLEDState = 0; |
||||
|
||||
void setup() { |
||||
|
||||
// Configure the user LED pin as output
|
||||
pinMode(usrLED, OUTPUT); |
||||
digitalWrite(usrLED, usrLEDState); |
||||
|
||||
// Enable the MIDI to listen on all channels
|
||||
MIDI.begin(MIDI_CHANNEL_OMNI);
|
||||
Serial.begin(57600); // Enable the serial monitor
|
||||
Wire.begin(); // Enable the I2C bus for controlling the codec
|
||||
delay(5); |
||||
|
||||
delay(100); |
||||
codecControl.disable(); // Turn off the codec first (in case it was in an unknown state)
|
||||
delay(100); |
||||
AudioMemory(24); |
||||
|
||||
Serial.println("Enabling codec...\n"); |
||||
codecControl.enable(); // Enable the codec
|
||||
delay(100); |
||||
|
||||
|
||||
} |
||||
|
||||
void loop() {
|
||||
|
||||
///////////////////////////////////////////////////////////////////////
|
||||
// MIDI TESTING
|
||||
// Connect a loopback cable between the MIDI IN and MIDI OUT on the
|
||||
// GTA Pro. This test code will periodically send MIDI events which
|
||||
// will loop back and get printed in the Serial Monitor.
|
||||
///////////////////////////////////////////////////////////////////////
|
||||
int type, note, velocity, channel, d1, d2; |
||||
|
||||
// Send MIDI OUT
|
||||
int cc, val=0xA, channelSend = 1; |
||||
for (cc=32; cc<40; cc++) { |
||||
MIDI.sendControlChange(cc, val, channelSend); val++; channelSend++; |
||||
delay(100); |
||||
MIDI.sendNoteOn(10, 100, channelSend); |
||||
delay(100); |
||||
} |
||||
|
||||
if (MIDI.read()) { // Is there a MIDI message incoming ?
|
||||
byte type = MIDI.getType(); |
||||
Serial.println(String("MIDI IS WORKING!!!")); |
||||
switch (type) { |
||||
case NoteOn: |
||||
note = MIDI.getData1(); |
||||
velocity = MIDI.getData2(); |
||||
channel = MIDI.getChannel(); |
||||
if (velocity > 0) { |
||||
Serial.println(String("Note On: ch=") + channel + ", note=" + note + ", velocity=" + velocity); |
||||
} else { |
||||
Serial.println(String("Note Off: ch=") + channel + ", note=" + note); |
||||
} |
||||
break; |
||||
case NoteOff: |
||||
note = MIDI.getData1(); |
||||
velocity = MIDI.getData2(); |
||||
channel = MIDI.getChannel(); |
||||
Serial.println(String("Note Off: ch=") + channel + ", note=" + note + ", velocity=" + velocity); |
||||
break; |
||||
default: |
||||
d1 = MIDI.getData1(); |
||||
d2 = MIDI.getData2(); |
||||
Serial.println(String("Message, type=") + type + ", data = " + d1 + " " + d2); |
||||
} |
||||
t = millis(); |
||||
} |
||||
|
||||
// If no MIDI IN activity, print a message every 10 seconds
|
||||
if (millis() - t > 10000) { |
||||
t += 10000; |
||||
Serial.println("(no MIDI activity, check cables)"); |
||||
} |
||||
|
||||
// Toggle the USR LED state
|
||||
usrLEDState = ~usrLEDState; |
||||
digitalWrite(usrLED, usrLEDState); |
||||
|
||||
} |
||||
|
Loading…
Reference in new issue