You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
83 lines
2.3 KiB
83 lines
2.3 KiB
6 years ago
|
# file DFRobot_AS3935_lightning_sensor.py
|
||
|
|
#
|
||
|
|
# SEN0290 Lightning Sensor
|
||
|
|
# This sensor can detect lightning and display the distance and intensity of the lightning within 40 km
|
||
|
|
# It can be set as indoor or outdoor mode.
|
||
|
|
# The module has three I2C, these addresses are:
|
||
|
|
# AS3935_ADD1 0x01 A0 = High A1 = Low
|
||
|
|
# AS3935_ADD3 0x03 A0 = High A1 = High
|
||
|
|
# AS3935_ADD2 0x02 A0 = Low A1 = High
|
||
|
|
#
|
||
|
|
#
|
||
|
|
# Copyright [DFRobot](http://www.dfrobot.com), 2018
|
||
|
|
# Copyright GNU Lesser General Public License
|
||
|
|
#
|
||
|
|
# version V0.1
|
||
|
|
# date 2018-11-13
|
||
|
|
|
||
|
|
import time
|
||
|
|
from DFRobot_AS3935_Lib import DFRobot_AS3935
|
||
|
|
import RPi.GPIO as GPIO
|
||
|
|
from datetime import datetime
|
||
|
|
|
||
|
|
#I2C address
|
||
|
|
AS3935_I2C_ADDR1 = 0X01
|
||
|
|
AS3935_I2C_ADDR2 = 0X02
|
||
|
|
AS3935_I2C_ADDR3 = 0X03
|
||
|
|
|
||
|
|
#Antenna tuning capcitance (must be integer multiple of 8, 8 - 120 pf)
|
||
|
|
AS3935_CAPACITANCE = 96
|
||
|
|
IRQ_PIN = 37
|
||
|
|
|
||
|
|
#Indoor/outdoor mode selection
|
||
|
|
AS3935_INDOORS = 0
|
||
|
|
AS3935_OUTDOORS = 1
|
||
|
|
AS3935_MODE = AS3935_INDOORS
|
||
|
|
|
||
|
|
#Enable/disable disturber detection
|
||
|
|
AS3935_DIST_DIS = 0
|
||
|
|
AS3935_DIST_EN = 1
|
||
|
|
AS3935_DIST = AS3935_DIST_EN
|
||
|
|
|
||
|
|
GPIO.setmode(GPIO.BOARD)
|
||
|
|
|
||
|
|
sensor = DFRobot_AS3935(AS3935_I2C_ADDR3, bus = 1)
|
||
|
|
sensor.reset()
|
||
|
|
#Configure sensor
|
||
|
|
sensor.manualCal(AS3935_CAPACITANCE, AS3935_MODE, AS3935_DIST)
|
||
|
|
|
||
|
|
# Connect the IRQ and GND pin to the oscilloscope.
|
||
|
|
# uncomment the following sentences to fine tune the antenna for better performance.
|
||
|
|
# This will dispaly the antenna's resonance frequency/16 on IRQ pin (The resonance frequency will be divided by 16 on this pin)
|
||
|
|
# Tuning AS3935_CAPACITANCE to make the frequency within 500/16 kHz ± 3.5%
|
||
|
|
#
|
||
|
|
# sensor.setLcoFdiv(0)
|
||
|
|
# sensor.setIrqOutputSource(3)
|
||
|
|
|
||
|
|
def callback_handle(channel):
|
||
|
|
global sensor
|
||
|
|
time.sleep(0.005)
|
||
|
|
intSrc = sensor.getInterruptSrc()
|
||
|
|
if intSrc == 1:
|
||
|
|
lightningDistKm = sensor.getLightningDistKm()
|
||
|
|
print('Lightning occurs!')
|
||
|
|
print('Distance: %dkm'%lightningDistKm)
|
||
|
|
|
||
|
|
lightningEnergyVal = sensor.getStrikeEnergyRaw()
|
||
|
|
print('Intensity: %d '%lightningEnergyVal)
|
||
|
|
elif intSrc == 2:
|
||
|
|
print('Disturber discovered!')
|
||
|
|
elif intSrc == 3:
|
||
|
|
print('Noise level too high!')
|
||
|
|
else:
|
||
|
|
pass
|
||
|
|
#Set to input mode
|
||
|
|
GPIO.setup(IRQ_PIN, GPIO.IN)
|
||
|
|
#Set the interrupt pin, the interrupt function, rising along the trigger
|
||
|
|
GPIO.add_event_detect(IRQ_PIN, GPIO.RISING, callback = callback_handle)
|
||
|
|
|
||
|
|
while True:
|
||
|
|
time.sleep(1.0)
|
||
|
|
|
||
|
|
|