You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
81 lines
3.0 KiB
81 lines
3.0 KiB
/*************************************************************************
|
|
* This demo uses the BALibrary library to provide enhanced control of
|
|
* the TGA Pro board.
|
|
*
|
|
* The latest copy of the BA Guitar library can be obtained from
|
|
* https://github.com/Blackaddr/BALibrary
|
|
*
|
|
* This program can be used to find out the calibration values for each of your POTs
|
|
* on the Blackaddr Audio Expansion Control Board.
|
|
*
|
|
* USE THE ARDUINO SERIAL MONITOR TO PERFORM THE CALIBRATION
|
|
*
|
|
* When prompted turn the appropriate POT in the specified direction and
|
|
* enter any character on the terminal input line and press enter to send the character.
|
|
*/
|
|
#include "BALibrary.h"
|
|
|
|
using namespace BALibrary;
|
|
|
|
// Create physical controls for Expansion Board, 2 switches, 3 pots, 0 encoders, 2 LEDs
|
|
BAPhysicalControls controls(BA_EXPAND_NUM_SW, BA_EXPAND_NUM_POT, 0, BA_EXPAND_NUM_LED);
|
|
|
|
void setup() {
|
|
delay(100);
|
|
Serial.begin(57600);
|
|
delay(500); // long delay to wait for Serial to init
|
|
|
|
TGA_PRO_EXPAND_REV2(); // Set the expansion board revision
|
|
|
|
// put your setup code here, to run once:
|
|
Serial.println("Calibrating POT1");
|
|
Potentiometer::Calib pot1Calib = Potentiometer::calibrate(BA_EXPAND_POT1_PIN);
|
|
if (pot1Calib.min == pot1Calib.max) { Serial.println("\n!!! The knob didn't appear to move. Are you SURE you're turning the right knob? !!!"); }
|
|
|
|
Serial.println("\nCalibrating POT2");
|
|
Potentiometer::Calib pot2Calib = Potentiometer::calibrate(BA_EXPAND_POT2_PIN);
|
|
if (pot2Calib.min == pot2Calib.max) { Serial.println("\n!!! The knob didn't appear to move. Are you SURE you're turning the right knob? !!!"); }
|
|
|
|
Serial.println("\nCalibrating POT3");
|
|
Potentiometer::Calib pot3Calib = Potentiometer::calibrate(BA_EXPAND_POT3_PIN);
|
|
if (pot3Calib.min == pot3Calib.max) { Serial.println("\n!!! The knob didn't appear to move. Are you SURE you're turning the right knob? !!!"); }
|
|
|
|
// Create the controls using the calib values
|
|
controls.addPot(BA_EXPAND_POT1_PIN, pot1Calib.min, pot1Calib.max, pot1Calib.swap);
|
|
controls.addPot(BA_EXPAND_POT2_PIN, pot2Calib.min, pot2Calib.max, pot2Calib.swap);
|
|
controls.addPot(BA_EXPAND_POT3_PIN, pot3Calib.min, pot3Calib.max, pot3Calib.swap);
|
|
|
|
// Add the pushbuttons
|
|
controls.addSwitch(BA_EXPAND_SW1_PIN);
|
|
controls.addSwitch(BA_EXPAND_SW2_PIN);
|
|
|
|
// Setup the LEDs
|
|
controls.addOutput(BA_EXPAND_LED1_PIN);
|
|
controls.setOutput(BA_EXPAND_LED1_PIN, 0);
|
|
controls.addOutput(BA_EXPAND_LED2_PIN);
|
|
controls.setOutput(BA_EXPAND_LED2_PIN, 0);
|
|
|
|
Serial.println("DONE SETUP! Try turning knobs and pushing buttons!\n");
|
|
|
|
}
|
|
|
|
void loop() {
|
|
// put your main code here, to run repeatedly:
|
|
float value;
|
|
for (unsigned i=0; i<BA_EXPAND_NUM_POT; i++) {
|
|
if (controls.checkPotValue(i, value)) {
|
|
Serial.println(String("POT") + (i+1) + String(" new value: ") + value);
|
|
}
|
|
}
|
|
|
|
// Check pushbuttons
|
|
for (unsigned i=0; i<BA_EXPAND_NUM_SW; i++) {
|
|
if (controls.isSwitchToggled(i)) {
|
|
Serial.println(String("Button") + (i+1) + String(" pushed!"));
|
|
controls.toggleOutput(i);
|
|
}
|
|
}
|
|
|
|
delay(10);
|
|
|
|
}
|
|
|