You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
132 lines
3.9 KiB
132 lines
3.9 KiB
/*************************************************************************
|
|
* This demo is used for manufacturing testing on the TGA Pro Expansion
|
|
* Control Board.
|
|
*
|
|
* This will test the following on the TGA Pro:
|
|
*
|
|
* - Audio INPUT and OUTPUT JACKS
|
|
* - Midi INPUT and Midi OUTPUT jacks
|
|
* - MEM0 (if installed)
|
|
* - MEM1 (if installed)
|
|
* - User LED
|
|
*
|
|
* This will also test the Expansion Control Board (if installed):
|
|
*
|
|
* - three POT knobs
|
|
* - two pushbutton SWitches
|
|
* - two LEDs
|
|
* - headphone output
|
|
*
|
|
* SETUP INSTRUCTIONS:
|
|
*
|
|
* 1) Connect an audio source to AUDIO INPUT.
|
|
* 2) Connect AUDIO OUTPUT to amp, stereo, headphone amplifier, etc.
|
|
* 3) if testing the MIDI ports, connect a MIDI cable between MIDI INPUT and MIDI OUTPUT
|
|
* 4) comment out any tests you want to skip
|
|
* 5) Compile and run the demo on your Teensy with TGA Pro.
|
|
* 6) Launch the Arduino Serial Monitor to see results.
|
|
*
|
|
* TESTING INSTRUCTIONS:
|
|
*
|
|
* 1) Check the Serial Monitor for the results of the MIDI testing, and external memory testing.
|
|
* 2) Confirm that the audio sent to the INPUT is coming out the OUTPUT.
|
|
* 3) Confirm the User LED is blinking every 1 or 2 seconds
|
|
*
|
|
* If using the Expansion Control Board:
|
|
*
|
|
* 1) Try pushing the pushbuttons. When pushed, they should turn on their corresponding LED.
|
|
* 2) Try turn each of the knobs one at a time. They should adjust the volume.
|
|
*
|
|
* The latest copy of the BA Guitar library can be obtained from
|
|
* https://github.com/Blackaddr/BALibrary
|
|
*
|
|
*/
|
|
|
|
#define RUN_MIDI_TEST // Uncomment this line to run the MIDI test.
|
|
//#define RUN_MEMO_TEST // Uncomment this line to run the MEM0 test.
|
|
//#define RUN_MEM1_TEST // (Teensy 3.5/3/6 only!) Uncomment this line to run the MEM1 test.
|
|
|
|
#include <Audio.h>
|
|
#include "BALibrary.h"
|
|
|
|
using namespace BALibrary;
|
|
|
|
AudioInputI2S i2sIn;
|
|
AudioOutputI2S i2sOut;
|
|
|
|
// Audio Thru Connection
|
|
AudioConnection patch0(i2sIn,0, i2sOut, 0);
|
|
AudioConnection patch1(i2sIn,1, i2sOut, 1);
|
|
|
|
BAAudioControlWM8731 codec;
|
|
BAGpio gpio; // access to User LED
|
|
|
|
#if defined(RUN_MEMO_TEST)
|
|
BASpiMemoryDMA spiMem0(SpiDeviceId::SPI_DEVICE0);
|
|
#endif
|
|
|
|
#if defined(RUN_MEM1_TEST) && !defined(__IMXRT1062__) // SPI1 not supported on T4.0
|
|
BASpiMemoryDMA spiMem1(SpiDeviceId::SPI_DEVICE1);
|
|
#endif
|
|
|
|
// Create a control object using the number of switches, pots, encoders and outputs on the
|
|
// Blackaddr Audio Expansion Board.
|
|
BAPhysicalControls controls(BA_EXPAND_NUM_SW, BA_EXPAND_NUM_POT, BA_EXPAND_NUM_ENC, BA_EXPAND_NUM_LED);
|
|
|
|
void configPhysicalControls(BAPhysicalControls &controls, BAAudioControlWM8731 &codec);
|
|
void checkPot(unsigned id);
|
|
void checkSwitch(unsigned id);
|
|
bool spiTest(BASpiMemory *mem, int id); // returns true if passed
|
|
bool uartTest(); // returns true if passed
|
|
|
|
unsigned loopCounter = 0;
|
|
|
|
void setup() {
|
|
Serial.begin(57600);
|
|
while (!Serial) { yield(); }
|
|
delay(500);
|
|
|
|
// Disable the audio codec first
|
|
codec.disable();
|
|
delay(100);
|
|
AudioMemory(128);
|
|
codec.enable();
|
|
codec.setHeadphoneVolume(0.8f); // Set headphone volume
|
|
configPhysicalControls(controls, codec);
|
|
|
|
// Run the initial Midi connectivity and SPI memory tests.
|
|
#if defined(RUN_MIDI_TEST)
|
|
if (uartTest()) { Serial.println("MIDI Ports testing PASSED!"); }
|
|
#endif
|
|
|
|
#if defined(RUN_MEMO_TEST)
|
|
SPI_MEM0_1M();
|
|
//SPI_MEM0_4M();
|
|
spiMem0.begin(); delay(10);
|
|
if (spiTest(&spiMem0, 0)) { Serial.println("SPI0 testing PASSED!");}
|
|
#endif
|
|
|
|
#if defined(RUN_MEM1_TEST) && !defined(__IMXRT1062__)
|
|
SPI_MEM1_1M();
|
|
//SPI_MEM1_4M();
|
|
spiMem1.begin(); delay(10);
|
|
if (spiTest(&spiMem1, 1)) { Serial.println("SPI1 testing PASSED!");}
|
|
#endif
|
|
|
|
Serial.println("Now monitoring for input from Expansion Control Board");
|
|
}
|
|
|
|
void loop() {
|
|
|
|
checkPot(0);
|
|
checkPot(1);
|
|
checkPot(2);
|
|
checkSwitch(0);
|
|
checkSwitch(1);
|
|
|
|
delay(20);
|
|
loopCounter++;
|
|
if ((loopCounter % 100) == 0) {
|
|
gpio.toggleLed();
|
|
}
|
|
}
|
|
|